Araldite ARA-400003 Standard Syringe Epoxy, 24 ml

It's been my go-to epoxy for many years, it works perfectly every time and I can absolutely depend on it.It doesn't set quickly, so that makes it really good because it's not a race against time to get the glue where you need it before it goes off, or, to remove glue where its ended up in exactly the place that you definitely didn't;t need it!The syringe dispenser makes it really easy to use, when I first used araldite it was in separate tubes, which is ok, but it's far more messy and you have to ensure you dispense the same proportion of both parts, it comes with a stick to mix it, but I just use tea/coffee stirrers, you only need to mix it for 30 seconds and you can tell when it's mixed when you cannot see any streaks in the resin.I use my stirrer to apply the glue, in my pictures I filled a void in a 3D printed part, although the epoxy is quite a "stiff" glue, it will fill gaps as it levels itself, this allowed the epoxy to fill around my "joint" piece which connected both haves, I placed my part face down on glossy card.You need to clamp your pieces to hold everything in place while it sets, you definitely don't want it setting with pieces in the wrong place because they're not coming apart ever, I use some cheap clamps and they work great.You can see on the front that the epoxy levelled and filled in the tiny gaps, resulting in everything being bonded incredibly well, you would break the bits that weren't glued before you had anywhere near any issue with the glued section.I left it clamped for 8 hours, after which I removed the clamps and then let it sit overnight, the following morning it lifted straight from the glossy paper and revealed a very clean joint. As this part is going to be painted, I used a coarse grit sandpaper to gently and methodically work over the surface until it was level with the printed parts, at that point I worked up in various grits to 3000, after which the area where the joint and glue was smooth and flat and you are unable to feel any difference in the surface between the printed parts and this joint section, it's completely merged into the whole part.It really is one of the best glues around.

I feel like this used to set faster. It seems to take about 8 hours but i remember in the past it was more like 30 minutes, which was sometimes very useful. Due to the design of the dispencer its sometimes difficult to get a 50/50 ratio but even when I make sure to do this, the cure time is long

Super quick drying, incredibly strong, worked perfectly with 3D printed parts. Really happy with the results.

I use all manner of adhesives for a wide number of hobby and work related tasks, so it's great to find quality products that fulfil a need. In my case Araldite Standard Syringe Epoxy does just that by providing an extremely strong and reliable epoxy glue that allows for repositioning for up to 2 hours. Unlike the majority of todays epoxy's that set (hold the glued item's position) in 5 minutes and cure (go rock hard) in an hour or so, the Araldite Standard Epoxy provides a genuine 60-120 minute working time (depending on thickness used, material used on and environmental conditions) and then cures in approximately 12-24 hours. This is perfect when performing a complex and long-winded repair where perfect positioning takes time and care.The epoxy dries clear but with a light glossy yellow tinge. It works perfectly on pretty much all finishes including Glass and Stone (less porous materials) and when set it's rock solid. I used it to repair an 8 inch crack in a large amethyst including sticking individual chips back into position and the quartz is now stuck firmer than it was when it was taken fresh from the ground.This is a great slower drying 2 part syringe epoxy that does its job well.

Works well, as Araldite always does BUT the mixer tubes are pointless, particularly as there's only two.The cap isn't a great idea either.I'll buy normal tubes next time.

Really easy to use. The glue is fantastic for sticking soles of shoes. Our Grandson has a tendency to drag his feet. Saves buying a new pair of £40.00 shoes. Dries very clear.

Plus points: the dispensing and mixing tube is great - last time I used 2 part araldite I remember mixing it on bits of carboard with match sticks - that's been consigned to history - the pack is great.Negative points:1 - despite the claims - it did not stick the plastic parts I bought it to stick, and I had thoroughly cleaned the parts with IPA before. I'll now need to try another adhesive of some sort.2 - there are only 2 mixing tubes so if you only use a little glue each time you could end up being left with a lot of adhesive in the tubes and then needing to mix together on a piece of card with a matchstickSo a bit disappointed to be honest

I usually use Araldite Rapid but for this job needed the strongest glue I could find. Takes 14 hours to fully cure, but provided you have the time and a good set of clamps it’s worth the wait